TORSO : Shorten or Lengthen, front and back

For TIGHT jumpsuits

*You will be asked to confirm your Torso (Z) measurement.

1. Zip the suit up, if possible, but remove the booties and allow them to slide up the leg.
2. Arch and then relax, but resist adjusting the suit.
3. Take a picture of you wearing the suit, front and back.
4. Email the pictures to our alterations department at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

For BAGGY jumpsuits

*You will be asked to confirm your Torso (Z) measurement.

1. Zip the suit up.
2. Make sure crotch of jumpsuit is pulled up against the body.
3. CENTER FRONT CHECK. At the center front of the body, gather and "pinch" the excess material until your fingers are against the body.
4. Arch deeply, then measure the remaining pinched amount. This will tell us how much needs to be taken out of the suit length.
5. IF the arching pulls out all of the pinched material but the suit still feels long, then do a side seam check. If not, skip to step 7.
6. SIDE SEAM CHECK. Stand upright and pinch the side seam to shorten the length. Slowly point the toes to lengthen the suit -as if in a flat-track body position. Come back to standing flat and measure the remaining pinched amount. This will tell us how much needs to be taken out of the side seam length.
7. Please take pictures with multiple angles of this area, including the pinched amount, and email them to us at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

SHOULDERS: Narrow or widen

For TIGHT jumpsuits

*You will be asked to confirm a few measurements; Shoulders (D), Upper and Lower arm lengths (C&B).

1. Zip the suit up, if possible.
2. Make sure the center-back seam, below the collar, is against the spine.
3. Keep the upper arms down against the body and bend the forearms 90 degrees.
4. Take a picture of you wearing the suit, front, back, and side-profile.
5. Email the pictures to our alterations department at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

For BAGGY jumpsuits

*You will be asked to confirm a few measurements; Shoulders (D), Upper and Lower arm lengths (C&B).

1. Zip the suit up.
2. Make sure the center-back seam, below the neck, is against the spine.
3. Keep the upper arms down against the body and bend the forearms 90 degrees.
4. Pinch the extra material at the top of the shoulder.
5. Place the measuring device on the top side of the pinched material, against the body. This will tell us how much needs to be taken out.
6. Please take pictures with multiple angles of this area, including the pinched amount, and email them to us at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

ARMS: Shorten or Lengthen

For jumpsuits & jackets

*You will be asked to confirm a few measurements; Shoulders (D), Upper and Lower arm lengths (C&B).

1. Zip up the main zipper.

1. Make sure the center-back seam, below the collar, is against the spine.
2. Make sure the seam between the upper and lower arm is above the elbow by about an inch or two.
3. Bend the elbow until the arm is about 90 degrees, but keep the upper arm against the body.
4. If there is extra material, "pinch" the excess until the fingers are against the body, and measure this amount. Take a picture to capture the info.
5. Take a side-profile picture that shows the full, bent arm.
6. Next stand with arms away from the body, flat from the shoulders to the wrist (like a wingsuiter).
7. Take pictures of the front, making sure to show from head to hand.
8. Email the pictures to our alterations department at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

For wingsuits

*You will be asked to confirm a couple measurements; Shoulders (D) and Arm Length (WA).

1. Zip up the main zipper.

1. Make sure the center-back seam, below the collar, is against the spine.
2. Hold arms away from the body at full extension.
3. Take pictures of the front, making sure to show from head to hand.
4. Email the pictures to our alterations department at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

LEGS: Shorten or Lengthen

To LENGTHEN UPPER legs

*You will be asked to confirm a couple measurements; Upper Leg (M), and Inseam (N).

1. Put on the suit and skydiving rig, and zip it up.
2. Make sure the crotch is pulled up against the body, and the skydiving rig leg-straps are tightened.
3. Bend the knee and place the toe on a raised platform.
4. Place the measuring device on the top of the leg, with the end placed at the top of the kneecap and measure up the leg until about mid-thigh.
5. Take 2 pictures of you wearing the suit,
   1. From above looking down at your knee and the measuring device,
   2. From the side-profile, including lower leg.
6. Email the pictures to our alterations department at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

To LENGTHEN LOWER legs

*You will be asked to confirm a couple measurements; Upper Leg (M), and Inseam (N).

1. Put on the suit and skydiving rig, and zip it up.
2. Make sure the crotch is pulled up against the body, and the rig leg-straps are tightened.
3. Bend the knee and place the toe on a raised platform.
4. Remove the booties from the leg and press the inseam against the leg.
5. Place the measuring device at the bottom of the inseam and measure the gap to the platform, this will tell us how much to add at the inseam.
6. Take a pictures of you wearing the suit, from the side-profile, include upper leg.
7. Email the pictures to our alterations department at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

To SHORTEN UPPER legs

*You will be asked to confirm a couple measurements; Upper Leg (M), and Inseam (N).

1. Put on the suit and skydiving rig, and zip it up.
2. Make sure the crotch is pulled up against the body, and the rigs leg-straps are tightened.
3. Bend the knee and place the toe on a raised platform.
4. Gather the excess material above the top of the knee until the knee seam is above the kneecap and "pinch" the excess material until your fingers are against the body.
5. Place the measuring device on the top side of the pinched material, against the body. This will tell us how much needs to be taken out of the upper leg.
6. Please take pictures with multiple angles of this area, including the pinched amount, and email them to us at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

To SHORTEN LOWER legs

*You will be asked to confirm a couple measurements; Upper Leg (M), and Inseam (N).

1. Put on the suit and skydiving rig, and zip it up.
2. Make sure the crotch is pulled up against the body, and the rigs leg-straps are tightened.
3. Bend the knee and place the toe on a raised platform.
4. Make sure the knee seam is above the kneecap.
5. Point the toe.
6. Gather the excess material of the lower leg towards the top of the knee until the bootie is taut.
7. "Pinch" the excess material until your fingers are against the body.
8. Place the measuring device on the top side of the pinched material, against the body. This will tell us how much needs to be taken out of the upper leg.
9. Please take pictures with multiple angles of this area, including the pinched amount, and email them to us at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

CAMERA WINGS: Shorten or Lengthen

To LENGTHEN wings, to laterals

When the wing doesn't go all the way down to the lateral webbing on the skydiving rig. *You might be asked to provide a new Q1 measurement.

1. Put on the wings and skydiving rig, with everything zipped up and the leg-straps tightened.
2. Measure the gap between where the wing attaches to the waist, and the lateral webbing on the skydiving rig.
3. Take a picture of the measurement and take a full picture, at least from neck to thigh, including the wrist.
4. Email the pictures to our alterations department at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

To SHORTEN wings, to laterals

When the wing folds underneath the lateral webbing on the skydiving rig. *You will be asked to provide a new Q1 measurement.

1. Put on the wings and skydiving rig, with everything zipped up and the leg-straps tightened.
2. If possible, measure the extra material folded by the lateral webbing.
3. Take a picture of the folded wing, and take a full picture, at least from neck to thigh, including the wrist.
4. Email the pictures to our alterations department at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

To LENGTHEN wings, toward wrist

When the wing doesn't go far enough down the arm, toward the wrist. *You will be asked to provide a new arm length (A) measurement.

1. Put on the wings and skydiving rig, with everything zipped up and the leg-straps tightened.
2. Measure the gap between the wrist and where the wing attaches to the arm.
3. Take a full picture of this measurement, at least from neck to thigh, including the wrist.
4. Email the picture to our alterations department at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

To SHORTEN wings, up the arm

When the wing is too long on the arm. *You will be asked to provide a new arm length (A) measurement.

1. Put on the wings and skydiving rig, with everything zipped up and the leg-straps tightened.
2. OPTION 1. Fold the excess material at the end of the wrist, and "pinch" the excess until the fingers are against the arm. Measure this pinched amount and take a photo.
3. OPTION 2. Hold the measuring device with the end at the wrist and point to where on the ruler/arm you would like the wing to end. Take a photo.
4. Take a full picture of this area at least from neck to thigh, including the wrist.
5. Email the picture to our alterations department at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

CHEST, WAIST, HIPS: Too tight or too baggy

For TIGHT jumpsuits

*You will be asked to confirm a few measurements; Chest (H1), Waist (I) and Hips (J).

1. Zip the suit up as much as is comfortable, without hurting yourself or the zipper.
2. Press the top of the suit against the body.
3. Measure the distance between the zipper. Begin at the top of the suit, and repeat this every few inches down the suit until you reach the part of the suit that fits. These measurements will tell us how much to add.
4. Take a picture of you wearing the suit, front and back.
5. Email the pictures to our alterations department at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

For BAGGY jumpsuits

*You will be asked to confirm a few measurements; Chest (H1), Waist (I) and Hips (J).

1. Zip the suit up.
2. Make sure crotch of jumpsuit is pulled up against the body.
3. Make sure the body zipper is at the middle of your torso, and using your fingers "pinch" the excess material equally on both sides of the body.
4. Measure the amount that is pinched, and take a picture of this area.
5. Repeat this for the areas that have excess material.
6. Please take pictures with multiple angles of these areas, including the pinched amount, and email them to us at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

THIGHS AND KNEES: Too tight or too baggy

For TIGHT jumpsuits

*You will be asked to confirm a couple measurements; Upper thigh (K), and Knee at 90 degrees (L).

1. Wearing your skydiving shoes, and -if possible, put your legs into the suit/booties, and bring the crotch of the suit up and against the body.
2. Take multiple pictures at different angles, both standing and squatting* -if possible. *Do not hurt yourself! If the suit pinches you, do not do this.
3. It's helpful if, in the pictures, you point to the areas that are the tightest.
4. Email the pictures to our alterations department at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

For BAGGY jumpsuits

*You will be asked to confirm a couple measurements; Upper thigh (K), and Knee at 90 degrees (L).

1. Zip the suit up.
2. Make sure crotch of jumpsuit is pulled up against the body.
3. THIGHS. Make sure the inseam is at the inside of your thigh, pull the side-seam away from your thigh and use your fingers to "pinch" the excess material on the side-seam. Pinch the excess right up against the body.
4. While holding the pinched amount, squat and return to standing. 
5. Measure the amount that is pinched, and take a picture of this area.
6. Repeat this for the knee, if needed.
7. Please take pictures with multiple angles of these areas, including the pinched amount, and email them to us at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

BOOTIE CIRCUMFERENCE: Too tight or too baggy

For TIGHT booties

*You will be asked to confirm the shoe circumference.

1. Wear your skydiving shoes and put your feet into the booties -as much as possible.
2. If you have an inseam zipper, zip it closed as much as is comfortable, without hurting yourself or the zipper, and measure 2 things: 1.) measure the gap at the bottom of the suit. 2.) measure the distance between the bottom of the suit and where the inseam zipper ends. Take photos of these areas.
3. If the bootie does not have an inseam zipper, grab the bottom of the back of the leg, at the elastic, and pull back as much as possible. Take a photo of this area, from a few different angles.
4. Email the pictures to our alterations department at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

For BAGGY booties

*You will be asked to confirm the shoe circumference.

1. Wear your skydiving shoes and put your feet into the booties.
2. If you have an inseam zipper, zip it closed.
3. At the inseam, pull the extra material away from your shoe and use your fingers to "pinch" the excess material, right up against the shoe.
4. Measure the amount that is pinched, and take a picture of this area.
5. Please take pictures with multiple angles of these areas, including the pinched amount, and email them to us at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

BICEP AND FOREARM CIRCUMFERENCE: Too tight or too baggy

For TIGHT arms

*You will be asked to confirm a couple measurements; Bicep (E) and Forearm (F).

1. Put your arm into the sleeve -as much as possible.
2. Make sure the seam between the upper and lower arm is above the elbow by about an inch or two.
3. Take multiple pictures at different angles, with the arm straight and bent* -if possible. *Do not hurt yourself! If the suit pinches you, do not do this.
4. It's helpful if, in the pictures, you point to the areas that are the tightest.
5. Email the pictures to our alterations department at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

For BAGGY arms

*You will be asked to confirm a couple measurements; Bicep (E) and Forearm (F).

1. Wear the thickest layer you'd normally wear (ex. base-layer) and put your arm into the sleeve.
2. Make sure the seam between the upper and lower arm is above the elbow by about an inch or two.
3. FLEX!
4. At the inside-seam, pull the extra material away from your arm and use your fingers to "pinch" the excess material, right up against the arm.
5. Measure the amount that is pinched, and take a picture of this area.
6. Please take pictures with multiple angles of these areas, including the pinched amount, and email them to us at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

NECK CIRCUMFERENCE: Too tight or too baggy

For TIGHT neck

*You will be asked to confirm the neck circumference.

1. Zip the suit up as much as is comfortable, without hurting yourself or the zipper.
2. Press the top of the suit against the body.
3. Measure the distance between the zipper. 
4. Take a picture of you wearing the suit; front, side, and back.
5. Email the pictures to our alterations department at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

For BAGGY neck

*You will be asked to confirm the neck circumference.

1. Wear the thickest layer you'd normally wear (ex. base-layer) and put the suit on and zipped up.
2. Make sure the main torso zipper and the center back seam, is right at the middle of your torso.
3. At the shoulder, pull the extra material away and use your fingers to "pinch" the excess material, right up against the shoulder.
4. Measure the amount that is pinched, and take a picture of this area.
5. Please take pictures with multiple angles of this area, including the pinched amount, and email them to us at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

WRIST AND ANKLE CIRCUMFERENCE: Too tight or too baggy

For TIGHT cuffs

*You will be asked to confirm the wrist or ankle circumference.

1. If possible, put your wrist/ankle through the cuff. *Do not hurt yourself! If they are so tight that you don't think you'll be able to take it off, don't put it on.
2. Take a photo. 
3. Email the pictures to our alterations department at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753

For LOOSE cuffs

*You will be asked to confirm the wrist or ankle circumference.

1. Wear the thickest layer you'd normally wear (ex. base-layer) and put your wrist/ankle through the cuff.
2. At the side-seam that runs down the cuff, pull the extra material away from your wrist/ankle and use your fingers to "pinch" the excess material, right up against the body and this seam.
3. Measure the amount that is pinched, and take a picture of this area.
4. Please take pictures with multiple angles of these areas, including the pinched amount, and email them to us at,

alterations@tonysuits.com

Office Hours: Monday - Thursday 8:30 - 5pm EST

PH: +1-813-788-4753